Fix Firmware Ml2165 Ml2168 Chip Reset Printer Samsung 676 Link -
There are two ways to solve the "Toner End of Life" or "Replace Toner" message on these printers:
Note on "Link 676": This likely refers to a specific vendor or a typo for the Samsung SCX-3405 or similar models that use the MLT-D101S or MLT-D111S toners. The guide below applies specifically to the ML-2165/2168 series.
If you cannot find the firmware file or the downgrade fails repeatedly, the “676 link” may refer to a hardware bridging trick. Advanced users can:
These hardware solutions are permanent and work even on locked V5.x firmware, but they require soldering skills.
The Samsung ML-2165 and ML-2168 are compact laser printers known for their affordability but high long-term costs due to restrictive toner cartridge chips
. Manufacturers use these chips to track page counts and block printing once a limit is reached, regardless of actual toner levels. To bypass these restrictions and enable cost-effective refilling, users often employ a fix firmware
—a modified software version that resets internal counters and allows the printer to operate without a chip. The Mechanics of the Chip Bypass Printers in the ML-2160 series utilize a reset chip
(often on the MLT-D101 cartridge) that contains resistors to signal the printer whether the drum is new. When a new cartridge is inserted, the printer burns a small resistor to reset its counter. A modified firmware (fix firmware) permanently alters the printer's logic to ignore this chip signal. : After flashing, the toner level will consistently show Physical Step
: Once the firmware is updated, the chip on the cartridge must be removed or covered with tape to prevent further communication with the printer. Preparation: Obtaining Required Data Fix firmware is typically single-device only
, meaning it is tied to a specific printer's hardware ID. To order or generate a fix, you must provide: Model Name
: Specifically whether it is the standard (ML-2165) or Wi-Fi (ML-2165W) version, as their firmwares are different. Serial Number
: A 15-character ID starting with "Z," found on the back of the device or via software tools like USB Device Viewer Firmware Version : Such as V1.01.01.12 or V3.00.01.14. CRUM Number : An 11-digit unique chip ID found in the Supplies Information Report Step-by-Step Installation Process There are two ways to solve the "Toner
The update is usually performed by connecting the printer via USB and following these steps: Samsung ML-2160 Firmware - ORPYS
To reset the toner chip on a Samsung ML-2165 or ML-2168 printer using a firmware fix, follow these steps to enable "chipless" printing. This process allows you to refill cartridges without replacing the expensive CRUM chips 1. Collect Required Printer Data
Before downloading a fix, you must identify your printer's specific identification numbers. Firmware fixes are unique to each device's serial number and CRUM chip. Configuration Report : Press and hold the Print Screen (or WPS) button for about 10 seconds
until the LED flashes once, then release. This report contains the Serial Number Firmware Version Supplies Information : Press and hold the Print Screen button again for about 15 seconds
until the LED stays green, then release. This report contains the CRUM Series 2. Enter Download Mode (Forced Mode)
To accept a new firmware file, the printer must often be put into a "forced" receiving state: Turn the printer Press and hold the Print Screen button, then press and hold the
After a few seconds, release both buttons. The LED should indicate it is in Download Mode. 3. Apply the Firmware Fix Once you have obtained the fix file (typically an file) from a specialized provider: Connect via USB
: Ensure the printer is connected directly to your computer via a USB cable. Run the Update : Drag and drop the firmware file onto the usbprns2.exe (or similar) application provided in your fix archive. Wait for Completion
: The printer's LED will blink rapidly while programming. Do
turn off the printer during this 1–2 minute process. The printer will reboot automatically when finished. 4. Final Chip Reset After the firmware update is complete: Physical Reset : Remove the toner cartridge and cover the chip
with a small piece of opaque tape or remove the chip entirely. Verification : Reinsert the cartridge. The printer should now report 100% toner and no longer prompt for a chip replacement. Samsung ML-2160 Firmware - ORPYS Note on "Link 676": This likely refers to
Since you're looking to share your experience with this firmware fix, it's helpful to highlight whether it actually saved you money on toner and if the installation was straightforward.
Here are three different versions of a review based on how your experience might have gone:
Option 1: The "Success Story" (Best for 5 Stars) ⭐⭐⭐⭐⭐ Headline: Finally freed my printer from expensive chips!
I was tired of the "toner low" messages even when the cartridge was still heavy. This firmware fix for my Samsung ML-2165 worked perfectly. Setup: The link provided (676) was easy to follow.
Result: The printer now recognizes refilled cartridges without needing a new reset chip every time. Savings: This will save me a fortune in the long run.
Tip: Make sure you follow the sequence exactly so you don't "brick" the machine.
Option 2: The "Technical/Instructional" Review (Helpful for others) ⭐⭐⭐⭐ Headline: Works well, but pay attention to the version.
This reset fix is a lifesaver for the ML-2168 series. It allows the printer to run without the CRUM chip communication.
Pros: Fast download, clear instructions, and instant reset of the page counter.
Cons: The process can be a bit nerve-wracking if you aren't tech-savvy.
Advice: Ensure your USB cable is securely connected and do not turn off the power during the update. It took about 5 minutes total to get it running. If you cannot find the firmware file or
Option 3: Short & Punchy (Best for quick browsing) ⭐⭐⭐⭐⭐ Headline: Does exactly what it says.
If you have a Samsung ML-2165 and want to use cheap toner refills, get this. The chip reset works flawlessly. No more "Incompatible Toner" errors. Highly recommended for anyone looking to cut printing costs. If you'd like to make this review even better, tell me: Did you run into any specific errors during the install? How much cheaper is your toner now? Was the website/link easy to navigate?
“fix firmware ml2165 ml2168 chip reset printer samsung 676 link”
Search for:
Crucial note: The exact version before 676 for M2165/M2168 is often v3.00.01.25 or v3.00.01.30.
Due to legal restrictions, I cannot provide direct links, but search these exact phrases:
⚠️ Warning: Avoid sketchy "crack" websites that ask for credit cards. Legitimate firmware files are free and should end in .exe or .ruf.
Most ML2165/ML2168 printers accept downgrades only in recovery mode:
The query refers to Samsung Xpress SL-M2165 and SL-M2168 monochrome laser printers.
The user is looking for a firmware fix or chip reset procedure to bypass toner cartridge restrictions, likely caused by a firmware update (version 676) that blocks third-party or refilled cartridges.
The “676” refers to a specific firmware version released by Samsung (now HP-owned) that introduced stricter cartridge authentication — meaning the printer checks for a genuine Samsung toner chip and refuses to work with reset or non‑original chips.
The goal is to roll back or modify the firmware to allow the printer to accept reset toner chips or refilled cartridges.
| Method | Success Rate | Risk Level | |--------|--------------|-------------| | Using a hardware chip resetter | Low after fw 676 | Low | | Buying a pre‑reset cartridge with “universal chip” | Medium | Low | | Downgrading firmware to version < 676 | High (if possible) | Medium | | Flashing modified firmware (custom) | High | High (brick risk) | | Covering chip contacts (tape trick) | None on 676 | Low |
Most community solutions point toward firmware downgrade as the only reliable fix.