Spreadtrum IMEI Tool V4.1 is often flagged as a hacker tool or virus (e.g., Trojan:Win32/Wacatac). This is because it directly accesses low-level hardware ports. However, only download from reputable repair forums (like GSMArena, XDA Developers, or Russian 4PDA) where checksums are verified.
Spreadtrum IMEI Tool V4.1 is a small, portable Windows-based utility designed for repairing or rewriting the IMEI (International Mobile Equipment Identity) numbers on mobile devices powered by Spreadtrum (UNISOC) chipsets. It is widely used in mobile phone repair shops to restore lost or corrupted IMEI data, often caused by firmware flashes or software corruption.
To validate a 15‑digit IMEI, compute the Luhn checksum for the first 14 digits; the 15th should match the checksum digit.
Spreadtrum IMEI Tool V4.1 is not merely software; it's a node in a network of technical practice, legal frameworks, and moral choices. It challenges us to craft systems that enable legitimate repair and reuse while discouraging misuse. A responsible future for such tools lies in transparent design, accountable distribution, and policies that respect both the sanctity of device identity and the rights of owners to repair and restore the devices they depend on.
—End
The Spreadtrum (SPD) IMEI Tool V4.1 (often referred to as the Spreadtrum WriteIMEI Tool) is a specialized Windows utility used to repair, restore, or write IMEI numbers on mobile devices powered by Spreadtrum/UNISOC chipsets. It is commonly used when a device loses its IMEI after flashing a new ROM, factory resetting, or due to software corruption, which often results in "Invalid IMEI" or "No Service" errors. Key Features
IMEI Repair: Restore the original IMEI for both SIM 1 and SIM 2.
Multi-Address Support: Beyond IMEI, it can write Bluetooth, Wi-Fi addresses, and Serial Numbers (SN).
Chipset Compatibility: Supports a wide range of SPD/UNISOC CPUs used in brands like Infinix, Tecno, itel, Realme, and Samsung. Spreadtrum Imei Tool V4.1
Mode Versatility: Works via Normal Mode (powered on with USB debugging) or Calibration/Diag Mode. Basic Usage Guide To use the tool effectively, follow these general steps:
Preparation: Install the necessary Spreadtrum USB Drivers on your PC and launch the WriteIMEI.exe application.
Configuration: Click on the Set or Mode Select button. If the phone is on, select Normal Mode; if it is off or in a specific diagnostic state, use Calibration Mode.
Port Selection: Ensure the correct COM port is selected under the "Port" settings, which can be verified in your PC's Device Manager.
Input Data: Enter the 15-digit stock IMEI number(s) found on the device's original box or under the battery.
Execution: Click Write or Start. Follow the on-screen prompts (such as powering off the phone or connecting it via USB) and wait for the "PASS" message.
Verification: Once completed, restart the device and dial *#06# to verify the restored IMEI.
Legal Disclaimer: Changing a device's IMEI to one other than its original factory-assigned number is illegal in many jurisdictions. This tool should only be used to restore the device's original IMEI for repair purposes. Spreadtrum IMEI Tool V4
Spreadtrum (SPD) WriteIMEI Tool V4.1 is a utility used to repair or restore the International Mobile Equipment Identity (IMEI) on devices powered by Spreadtrum/UNISOC chipsets. It is primarily used when a device displays an "Invalid IMEI" or "No Service" error after a firmware flash or software corruption. Prerequisites SPD USB Drivers
: Must be installed so your PC recognizes the phone in "Download Mode". Original IMEI
: Locate your device's original IMEI on the box or under the battery.
: A reliable micro-USB or USB-C cable for the data connection. Step-by-Step Guide Launch the Tool WriteIMEI.exe application from the extracted V4.1 folder on your PC. Configure Settings Settings icon , ensure "IMEI1" (and "IMEI2" if dual-SIM) is checked. to apply these configurations. Input IMEI
: Enter your device’s original 15-digit IMEI into the provided input fields. Initiate Writing ) button. The tool will now wait for the device to connect. Connect the Device Power off your phone completely. Volume Down
(or sometimes Volume Up) key and connect it to the PC via USB. Device Manager
under "Ports (COM & LPT)" to ensure it appears as an "SPD" or "UNISOC" device. Completion
: The tool will automatically begin the process. Once finished, a green message will appear. Critical Warnings Click Write IMEI
: Changing an IMEI to anything other than the original factory-assigned number is in many regions and can lead to network blacklisting.
: This tool interacts with the device's NVRAM; incorrect usage can lead to permanent loss of signal or "bricking" the phone. Do you have the SPD USB drivers
installed, or would you like help finding the correct ones for your OS?
The Spreadtrum IMEI Tool is a small, Windows-based utility designed specifically to write or repair IMEI numbers on devices powered by Spreadtrum processors (SC6531, SC7715, SC9820, SC9832, etc.).
The V4.1 version is particularly significant because it offers a more user-friendly interface compared to older, command-line based methods. It allows technicians to restore the "Unknown Baseband" error or "Null IMEI" status without needing complex boxes like Volcano or Miracle—though having drivers installed is non-negotiable.
You might wonder, “Why would my IMEI become corrupted in the first place?” Common scenarios include:
Sometimes, entering deep engineering modes (##3646633##) and resetting the NVRAM accidentally deletes the IMEI. V4.1 is the only low-level fix before resorting to a full re-flash.